Browse all practice questions for the Chromatography Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Chromatography Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Which of the following is a primary use of thin-layer chromatography?
  • In affinity chromatography, provide a typical ligand-target pair used in practice.
  • What does N represent in chromatography and how is the height of a theoretical plate defined?
  • Which detector is universal but typically less sensitive than mass spectrometry?
  • Describe retention mechanism in ion-exchange chromatography and how pH and counterions influence it.
  • Why is column equilibration with mobile phase important before sample injection?
  • The mobile phase is described as:
  • What are common sample preparation approaches before chromatographic analysis for trace-level analysis?
  • How can TLC spots be visualized?
  • In what year was the term chromatography first used?
  • Which factors determine the choice of carrier gas in gas chromatography, and what are the typical characteristics of common carrier gases?
  • Explain detector saturation and when it becomes a concern in quantitative LC-UV methods.
  • The stationary phase is described as:
  • In chromatography, which statement about the mobile phase is correct?
  • Which scenario favors using isocratic elution?
  • What is TLC mainly used for?
  • In the van Deemter equation, what does H denote?
  • Headspace sampling is typically used for analyzing which type of analytes?
  • If the mobile phase becomes more polar, polar compounds typically move ?
  • To improve separation of polar compounds on normal-phase TLC, which mobile phase choice is typically used?
  • What is gradient elution in HPLC, and when is it preferred over isocratic elution?
  • What is the fundamental difference between theoretical plates and real plate number in chromatography?
  • A compound that moves far up the plate is typically:
  • How does a nonpolar compound behave in column chromatography?
  • How is the limit of detection (LOD) defined via signal-to-noise?
  • Which parameter is typically varied to test robustness?
  • Explain accuracy, precision, and bias in method validation.
  • What happens if the solvent is too polar?
  • What is robustness in method validation, and how is it tested?
  • In normal-phase TLC, which compounds move fastest up the plate?
  • In normal-phase TLC, which compounds move slowest?
  • Why is silica gel considered polar?
  • Which statement best describes the primary purpose of column chromatography?
  • Which parameter is inversely related to peak broadening and related to the plate count?
  • When should TLC development be stopped?
  • Which statement describes the stationary phase in TLC as accurate?
  • Why are residuals important when evaluating a calibration curve?
  • Which statement best describes the principle behind chromatography as used by Tsvet?
  • In ion-exchange chromatography, what factors govern the binding and elution of analytes?
  • Which statement best differentiates LOQ from LOD in quantitative chromatography?
  • The pigments separated by Tsvet are primarily involved in which biological process?
  • What is the stationary phase in TLC?
  • What is a chromatographic baseline, and how can drift arise?
  • What does TLC stand for?
  • How is TLC used with column chromatography?
  • Which metric is used to quantify peak separation in a chromatogram?
  • Explain the meaning of the term 'theoretical plates' and its significance in chromatography column performance.
  • Define LOD and LOQ and explain how they differ from calibration range.
  • In chromatography, how is the limit of detection (LOD) defined and typically estimated?
  • Which application area is correctly paired with chromatography?
  • Define ruggedness in method validation and explain how it is assessed.
  • How can you recognize injection overload or detector saturation in a chromatogram?
  • Which strategy primarily increases chromatographic efficiency?
  • Why was Tsvet's work initially overlooked?
  • What role does a mass spectrometer play in LC-MS, and what information does it provide?
  • Describe GC vs GC-MS detectors and typical analyte classes for each.
  • What is peak symmetry and why is it important for integration accuracy?
  • What happens to compounds that interact weakly with the stationary phase?
  • Split injection in GC: what must be done to determine true concentration when a split ratio is used?
  • Which strategy would generally help separate a pair of polar solutes on a normal-phase TLC plate?
  • The limited early recognition of Tsvet's chromatography work was due to which factors?
  • How can sample preparation affect chromatographic outcomes, including recovery and interference?
  • In normal-phase TLC, how does polarity relate to Rf?
  • Which compound is commonly used as an unretained marker to determine the dead time tM in LC on a C18 column?
  • How do you determine the dead time experimentally in LC?
  • What is affinity chromatography and when is it advantageous?
  • Which component is responsible for introducing the sample into the flow stream in an HPLC system?
  • Which statement about the baseline in TLC is true?
  • What is chromatography?
  • Which statement about the height of a theoretical plate H is true?
  • Which elution mode is typically more suitable for analytes with wide polarity range and why?
  • What is the fundamental difference between partition chromatography and adsorption chromatography?
  • If a compound is highly polar, what is the expected effect on its Rf on silica gel TLC?
  • How is the number of theoretical plates N calculated from a chromatographic peak?
  • Which practice helps reduce tailing due to silanol interactions?
  • What is the baseline in TLC?
  • Which pigments did Tsvet separate?
  • Which of the following is a common stationary phase for TLC?
  • Why is split injection used in gas chromatography, and what is its typical impact on sensitivity and quantitation?
  • Two compounds with similar polarity on a normal-phase plate will have migration that is:
  • Distinguish between LOD and LOQ and typical criteria for their determination.
  • Which GC detector is a universal detector for organic compounds?
  • Compare the retention mechanisms of reversed-phase and ion-exchange chromatography.
  • In normal-phase TLC, the retention factor (Rf) is best described as:
  • What is the main purpose of column chromatography?
  • In reversed-phase HPLC, how does pH influence the retention of ionizable analytes?
  • What is dead time t_M and how is it measured?
  • Why use isotopically labeled internal standards in LC-MS quantitation?
  • What is the formula for resolution Rs between two peaks and what does a higher Rs indicate?
  • What is the stationary phase in column chromatography?
  • Explain method transfer between laboratories and key considerations.
  • In HPLC method development, what is the typical approach to mobile phase pH for ionizable compounds, and what are the implications for retention and peak shape?
  • In chromatography, what is retention time t_R?
  • What best describes carryover in chromatography and how is it minimized?
  • Which statement about the mobile phase is correct?
  • Between hexane and acetone under the same conditions, which tends to have a higher Rf on a normal-phase plate?
  • What role do pH and salt play in ion-exchange chromatography elution?
  • Describe a strategy to resolve co-eluting compounds when orthogonal separation is not feasible?
  • Which statement best describes how diffusion affects peak broadening in chromatography?
  • In LC-MS analysis, what are matrix effects and how can they be mitigated?
  • Which major chromatographic mode is correctly paired with its primary separation principle?
  • How does increasing column length impact resolution and backpressure in LC?
  • What is the linear dynamic range of a detector, and why is it important for quantitation?
  • What is orthogonal analysis in chromatography method development and why is it beneficial?
  • Where should the solvent level be relative to the baseline in TLC development?
  • What is the stationary phase?
  • What is a typical guideline for injection volume optimization in HPLC?
  • How does size-exclusion chromatography differentiate molecules, and what is meant by the void volume?
  • On a polar silica gel stationary phase, which type of compound is expected to elute fastest under typical conditions described?
  • Which description correctly identifies the TLC stationary phase used in the standard setup described?
  • What is split ratio and how does it affect sensitivity and sample consumption?
  • Which of the following is a common strategy to achieve chiral separation if a chiral column is not available?
  • What type of chromatography did Tsvet develop?
  • Is column chromatography generally fast or slow?
  • Explain tailing factor and how it affects quantitation and resolution. What causes tailing?
  • Which statement about detector response factor usage in multi-analyte quantitation is true?
  • How far above the bottom edge of a TLC plate is the baseline drawn?
  • What factors influence selectivity in liquid chromatography, and how can pH and ionic strength be used to adjust it?
  • What happens to compounds that interact strongly with the stationary phase?
  • In what scenario is planar chromatography particularly useful?
  • What feature of silica gel drives its polarity?
  • Isotopically labeled internal standards are used in LC-MS to mitigate matrix effects because:
  • What are planar chromatography techniques and give two common examples?
  • What property primarily determines the speed of migration in normal-phase TLC?
  • What does a retention time tell you in chromatography?
  • What does Rf stand for?
  • Which detector provides structural information and high sensitivity?
  • What is the trade-off when increasing column length in LC?
  • What constitutes acceptable linearity in a calibration curve for chromatography?
  • Explain the difference between normal-phase and reversed-phase chromatography.
  • In environmental analysis, chromatography is used to?
  • Which of the following correctly represents the Van Deemter equation and what each term represents?
  • Baseline separation means peaks are completely separated at baseline; broader peaks or tailing affect resolution.
  • In HPLC, what is the effect of increasing the mobile-phase flow rate on column efficiency and analysis time?
  • In chromatography, why might isocratic elution be inadequate for analyzing analytes with wide polarity ranges?
  • Which statement best describes when gradient elution should be used relative to isocratic?
  • What are the two phases in chromatography?
  • In forensic science, chromatography is used to?
  • In food testing, chromatography is used to?
  • If a TLC plate shows multiple spots, what does this indicate about the mixture?
  • How should a chromatogram with a blank, a standard, and a sample spike be interpreted for system suitability?
  • In GC, which statement about carrier gas properties best reflects typical practice?
  • In the van Deemter equation, what does the A term (eddy diffusion) represent?
  • What is two-dimensional LC (2D-LC) and in what scenarios is it typically employed?
  • Define injection solvent effect.
  • What factors influence mass spectrometric detection in LC-MS, particularly ionization methods like ESI vs APCI?
  • Which compounds generally have the lowest Rf values on silica gel TLC?
  • If polar compounds remain near baseline while nonpolar travel far, what does this indicate about the stationary phase?
  • Why can a chiral stationary phase separate enantiomers, and what are typical strategies to achieve this?
  • What is affinity chromatography and provide an example of a ligand-target pair exploited in this technique.
  • In thin-layer chromatography, what does the Rf value represent, and how is it used?
  • What is gradient time and re-equilibration, and why are they important for reproducibility in gradient elution?
  • What is back pressure in LC, and which factors influence it?
  • In GC, why is the choice of carrier gas important, and what are typical options?
  • In LC chromatography, what is a ghost peak and what are common causes?
  • What outcome on TLC suggests a pure compound?
  • If the stationary phase is polar and the mobile phase is nonpolar, what description fits the expected migration of nonpolar solutes compared to polar solutes under the same conditions?
  • What is chromatographic selectivity and how can you experimentally improve it?
  • Why are internal standards used in chromatographic quantitation, and what properties should a good internal standard have?
  • A chromatographic peak has t_R = 6.0 min and baseline width W_0.5 = 0.5 min. Using N = 5.54 (t_R/W_0.5)^2, what is the theoretical plate number N?
  • Why do compounds separate during chromatography?
  • Which statement accurately describes the mobile phase in column chromatography?
  • Which statement best describes how temperature affects chromatographic separation?
  • TLC can be used to monitor what in relation to reactions?
  • What is a detector response factor and how is it used in quantitation with multiple analytes?
  • What is size-exclusion chromatography and what determines separation in SEC?
  • What is the mobile phase in column chromatography?
  • Define the selectivity factor α and its role in peak separation.
  • Which statement about chromatography is true?
  • Which observation indicates detector saturation during a chromatographic run?
  • Which statement best describes gradient elution in liquid chromatography?
  • What is an internal standard (IS) and external standard method in quantitative chromatography? Give advantages of IS approach.
  • For typical adjacent peaks, a common target Rs value for baseline separation is greater than?
  • Which statement best describes polar vs nonpolar behavior on silica gel?
  • In reversed-phase HPLC, nonionized forms of ionizable solutes are typically more hydrophobic and show what behavior?
  • If two adjacent peaks exhibit Rs of 2.0, what does this indicate?
  • In reversed-phase HPLC, what best describes the distribution of solutes?
  • What is the mobile phase in TLC?
  • What happens if the mobile phase pH is near the silica pKa during a run?
  • What is the purpose of buffering mobile phases in HPLC, and how does pH control influence retention?
  • What adsorbent did Tsvet use in his original experiment?
  • Why do silanol groups on silica columns cause tailing for basic compounds, and how can this be mitigated?
  • What is headspace sampling, and when is it advantageous?
  • What mainly governs separation in normal-phase TLC?
  • Chromatography aims to
  • How is the capacity factor k' calculated?
  • Which statement correctly distinguishes partition chromatography from adsorption chromatography, with appropriate examples?
  • What tool is used to spot samples on a TLC plate?
  • Can an Rf value be exactly 0?
  • How does a polar compound behave in column chromatography?
  • Which year did Mihail Tsvet invent chromatography?
  • Can an Rf value be greater than 1?
  • If t_R = 4.0 minutes and t_M = 1.0 minute in an HPLC run, what is the retention factor k' and what is the typical desirable range for k' in HPLC?
  • What factors contribute to peak tailing in LC and how can tailing be mitigated?
  • If a compound interacts strongly with the stationary phase, it will elute:
  • What is the purpose of mobile phase pH control in reverse-phase HPLC of acidic or basic analytes?
  • How do you compute chromatographic resolution Rs for two adjacent peaks, and what Rs value indicates baseline separation?
  • Which statement about TLC Rf values is true?
  • What is a typical application area for 2D-LC?
  • In gradient LC, peak capacity is estimated from gradient time and which parameter?
  • What is a primary reason for using internal standards in LC-MS quantitation?
  • State the van Deemter equation and briefly describe each term.
  • How does column temperature affect retention and peak shapes in LC?
  • Baseline drift in chromatography is caused by which factors, and how can it be mitigated?
  • Which statement correctly describes normal-phase chromatography (NPC) and reversed-phase chromatography (RPC) in terms of stationary/mobile phases and the retention of nonpolar analytes?
  • How do FID and ECD detectors differ in principle and selectivity in GC?
  • What does a smaller Rf value indicate?
  • Which statement best describes the effect of increasing the number of theoretical plates on chromatographic peaks?
  • What is the formula for Rf?
  • In normal-phase TLC, which statement best describes the stationary phase?
  • How can TLC determine purity?
  • What is the effect of using an end-capped column on tailing?
  • Why might isotopically labeled internal standards be preferred over structural analogs for LC-MS quantitation?
  • In Rf calculation, which distance is the numerator?
  • What is a common consequence of using too high a flow rate in chromatography?
  • Which statement about k' (capacity factor) is true?
  • Outline a basic gradient optimization approach using two solutes to maximize resolution.
  • What is the purpose of a guard column and when should it be used?
  • What are the three main purposes of chromatography?
  • Which compounds generally have the highest Rf values on silica gel TLC?
  • What does a larger Rf value indicate?
  • Define robustness in method validation and provide an example.
  • Why should a good internal standard not co-elute with analytes?
  • In system suitability testing, what does a spike injection verify?
  • Which statement correctly defines the selectivity factor alpha and its effect on resolution Rs?
  • How can TLC identify the number of compounds in a mixture?
  • In GC, what is the relationship between selectivity and efficiency, and how does column chemistry influence each?
  • What is the effect of increasing column temperature on viscosity and retention time?
  • How does end-capping of silica columns influence peak tailing and peak symmetry?
  • Which statement about gradient elution is false?
  • Why should TLC samples not be too concentrated?
  • What is the role of the column oven in modern HPLC?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy